|
8 pin RJ45 (8P8C) female used in:
- Cisco Console port (at Catalyst 5000 Series Switch) The Cisco Consule port is used on the Cisco Catalyst 5000 Series Switch Supervisor Engine III
- Cisco Console (25) cable Use this cable to configure a Cisco router thru the Console port at the router.
- Cisco Console (9) cable Use this cable to configure a Cisco router thru the Console port at the router.
- Cisco Auxiliary port for Cisco 1000, 1600, 2500, 2600, and 3600 series routers The auxiliary port is configured as data terminal equipment (DTE)
- Cisco console port for Cisco 1000, 1600, 2500, 2600, And 3600 series routers The console and auxiliary ports on Cisco IOS routers are asynchronous serial ports. The console port is configured as data communications equipment (DCE)
- RS-232D
- Token Ring RJ-45 Alternate Connection to DB-9 Token Ring
- Avocent / Cybex / BlackBox XPSI and KV1609C serial control cards RJ45 connector of the 4XP / XP4000 / XP4040 / ServSwitch Multi EXP
- ISDN BRI RJ45
- GSM all-in-one (Unibox) cable
- Unibox, Griffin, Multi-Box, Nokia Flasher, UFS, Tornado GSM universal boxes devices for flashing cellular phones
- Motorola Radius Mic conector for SM50-GM300-p1225
- RocketPort Serialport Available at RocketPort serialport expansion cards.
- Ethernet 10/100Base-T ( RJ-45) connector Ethernet 10base-T / 100base-TX pinout. Widely used in ethernet network devices. Same connector and pinout for both 10Base-T, 100Base-TX and 1000base-T.
- Ethernet 1000Base-T (Gigabit ethernet) 1000 Base-T uses all pairs for bidirectional traffic in the RJ45 connector. cables used should be of Category 5e(nhanced), even though Category 5 cables usually works too.
- Ethernet 100Base-T4 100BASE-T4 is an early implementation of Fast Ethernet. It requires four twisted copper pairs and works with category 3 ethernet cable.
- CSU/DSU Network, T1, Fractional T1, T3 line RJ-48 used to connect a Bridge or Router to a 56K, CSU/DSU Network, T1, T3
- Power other Ethernet (POE) Power over Ethernet is a technology that allows IP telephones, wireless LAN Access Points, Security network cameras and other IP-based terminals to receive power, in parallel to data, over the existing CAT-5 Ethernet infrastructure without the need to make any modifications in it. Described by IEEE 802.3af standard.
Associated connector:
8 pin RJ45 (8P8C) male used in:
- Cisco Console port (at Catalyst 5000 Series Switch) The Cisco Consule port is used on the Cisco Catalyst 5000 Series Switch Supervisor Engine III
- Cisco Auxiliary port for Cisco 1000, 1600, 2500, 2600, and 3600 series routers The auxiliary port is configured as data terminal equipment (DTE)
- Cisco console port for Cisco 1000, 1600, 2500, 2600, And 3600 series routers The console and auxiliary ports on Cisco IOS routers are asynchronous serial ports. The console port is configured as data communications equipment (DCE)
- RS-232D
- Cisco Asynchronous-Line RJ45 to 68Pin SCSI cable
- Ethernet 10Base-T crossover cable This cable can be used to cascade hubs, or for connecting two Ethernet stations back-to-back without a hub. It works with both 10Base-T and 100Base-TX
- Ethernet 100Base-T4 crossover cable This cable can be used to connect two computers together without a hub, or to connect two hubs together (without using an uplink port). If you´re connecting two hubs together and one of them has an uplink port, use a straight cable.
- Cisco RJ45 RollOver cable
- Phase I PC modem cable
- Phase II PC modem cable
- Phase I Macintosh modem cable
- Phase II Macintosh modem cable
- RocketPort Serial (25) cable Use this cable to connect a RocketPort serialport card to a modem.
- Allied Telesyn/Network iQ1000 router serial port cable serial port for configuring router
- Ethernet 1Gb crossover cable 1Gb ethernet is autosensing, so crossover usually not needed
- ADC Pairgain 310F and 320F console used to connect PC to ADSL modem console
- ISDN BRI RJ45
- Unibox, Griffin, Multi-Box, Nokia Flasher, UFS, Tornado GSM universal boxes devices for flashing cellular phones
- LS 2208 Scaner to PS/2 connector adapter for connecting barcode scanner to ps/2 interface
- Yaesu Vertex Microphone for yaesu & vertex radios
- RocketPort Serialport Available at RocketPort serialport expansion cards.
- Cisco RJ45 to DB25 adapter
- Ethernet 10/100Base-T ( RJ-45) connector Ethernet 10base-T / 100base-TX pinout. Widely used in ethernet network devices. Same connector and pinout for both 10Base-T, 100Base-TX and 1000base-T.
- Ethernet 1000Base-T (Gigabit ethernet) 1000 Base-T uses all pairs for bidirectional traffic in the RJ45 connector. cables used should be of Category 5e(nhanced), even though Category 5 cables usually works too.
- Ethernet 10 / 100 Mbit (cat 5) network cable wiring This is most common cable for 10/100Base-T ethernet networks. This cable will work with both 10Base-T (10 Mbit ethernet) and 100Base-TX (100 Mbit ethernet) and is used to connect a network interface card to a hub or network outlet. These cables are sometimes called wipes.
- Ethernet 100Base-T4 100BASE-T4 is an early implementation of Fast Ethernet. It requires four twisted copper pairs and works with category 3 ethernet cable.
- Adtran CSUs RJ45 to DB9 cable e.g. works with Adtran MX2800
- CSU/DSU Network, T1, Fractional T1, T3 line RJ-48 used to connect a Bridge or Router to a 56K, CSU/DSU Network, T1, T3
- Power other Ethernet (POE) Power over Ethernet is a technology that allows IP telephones, wireless LAN Access Points, Security network cameras and other IP-based terminals to receive power, in parallel to data, over the existing CAT-5 Ethernet infrastructure without the need to make any modifications in it. Described by IEEE 802.3af standard.
- Cyclades cabling diagrams
- Baytech RPC-3 to DB9 serial port adapter Baytech RPC-3 RJ45 to DB9 null modem serial cable
|
|
>> >> >> >>
|
|
Sample query: rs-232
-
-
|
|
|
|