Hardware pinouts information and cables schemes

Amiga Video Expansion pinout

motherboard connector

bookmark this page

90 pin (36+54) EDGE connector layout

90 pin (36+54) EDGE connector
at the computer



Pin Name Dir Description
1RGB16-->Red Bit 0
2RGB17-->Red Bit 1
3LINELF-->Audio Line Out Left
4LINERT-->Audio Line Out Right
5C28D-->Pixel-Synchronous Clock
6+5V-+5 Volts DC (1 A)
7ARED-->Analog Red
8+5V-+5 Volts DC (1 A)
9GND-Digital Ground
10+12V-+12 Volts DC (40 mA)
11AGREEN-->Analog Green
12GND-Digital Ground
13GND-Digital Ground
14/CSYNC-->Composite Sync
15ABLUE-->Analog Blue
16/XCLKEN<--Genlock Clock Enable
17GND-Digital Ground
18BURST-->Burst Gate
19/C4-->3.55/3.58 MHz Clock
20GND-Digital Ground
21GND-Digital Ground
22/HSYNC-->Horizontal Sync (47 Ohm)
23RGB4-->Blue Bit 4
24GND-Digital Ground
25RGB7-->Blue Bit 7
26/VSYNC-->Vertical Sync (47 Ohm)
27RGB15-->Green Bit 7
28BLANK-->Video Blank
29RGB23-->Red 7
30/PIXELSW-->Genlock Overlay (47 Ohm)
31-5V--5 Volts DC
32GND-Digital Ground
33/XCLK<--Genlock Clock
34/C1-->C1 Clock
35+5V-+5 Volts DC (1 A)
36PSTROBE-->Printer Port Handshake
    
1GND-Digital Ground
2RGB20-->Red Bit 4
3RGB21-->Red Bit 5
4RGB22-->Red Bit 6
5GND-Digital Ground
6RGB12-->Green Bit 4
7RGB13-->Green Bit 5
8RGB14-->Green Bit 6
9GND-Digital Ground
10RGB5-->Blue Bit 5
11RGB6-->Blue Bit 6
12GND-Ground
13SOG-->Sync-On-Green Indicator
14TBASE-->50/60 Hz Software Clock Timebase
15CDAC-->7.09/7.16 MHz Clock
16PPOUT<->Printer Port Paper Out
17/C3-->3.55/3.58 MHz Clock
18PBUSY<->Printer Port Busy
19/LPEN<--Light Pen Input
20/PACK<->Printer Port Acknowledge Handshake
21PSEL-->Printer Port Select
22GND-Digital Ground
23PPD0<->Printer Port Data Bit 0
24PPD1<->Printer Port Data Bit 1
25PPD2<->Printer Port Data Bit 2
26PPD3<->Printer Port Data Bit 3
27PPD4<->Printer Port Data Bit 4
28PPD5<->Printer Port Data Bit 5
29PPD6<->Printer Port Data Bit 6
30PPD7<->Printer Port Data Bit 7
31/LED-->LED (Audio filter bypass) Setting
32GND-Digital Ground
33RAWLF-->Raw (Unfiltered) Audio Left
34AGND-Audio Ground
35RAWRT-->Raw (Unfiltered) Audio Right
36AGND-Audio Ground
37n/c-Reserved for future expansion
38n/c-Reserved for future expansion
39GND-Digital Ground
40GND-Digital Ground
41n/c-Reserved for future expansion
42n/c-Reserved for future expansion
43GND-Digital Ground
44GND-Digital Ground
45RGB18-->Red Bit 2
46RGB19-->Red Bit 3
47RGB8-->Green Bit 0
48RGB9-->Green Bit 1
49RGB10-->Green Bit 2
50RGB11-->Green Bit 3
51RGB0-->Blue Bit 0
52RGB1-->Blue Bit 1
53RGB2-->Blue Bit 2
54RGB3-->Blue Bit 3

Note: Direction is Motherboard relative Card.
Note: Do not mix analog & digital grounds.


This information should be correct, but may be not. Please, help us to improve this document!
Is this document CORRECT or INCORRECT? Your opinion will be used to establish document status (showed at the bottom).
Pinouts.ru > Motherboard connectors pinouts >  Pinout of Amiga Video Expansion and layout of 90 pin (36+54) EDGE connector
Document status: unknown
Source(s) of this and additional information: Amiga 4000 User"s Guide from Commodore, from Hardware Book 0 reports
Last updated at Sat Jun 25 2005. Submit additions or corrections for this document. Is this document correct or incorrect? What is your opinion?
[Discuss at the forum] [Back to index] [SUBMIT new pinout]
This page contain parts under Copyright © 2000-2007 by pinouts.ru team.
No any portion of this webpage may be reproduced in any form without visible direct link to this page provided. Webmaster permission required in any other cases.
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.
7871 hits since March 4, 2005