Hardware pinouts information and cables schemes

SCSI-3 External Hi D-Sub (Single-ended) pinout

hard drive connector

bookmark this page

SCA=Single connector Attachment

80 pin SCSI SCA-2 female connector layout

80 pin SCSI SCA-2 female connector



Drive connector: AMP Champ 557613-1 or AMP Champ 557114-5
Cable connector: AMP Champ 2-557103-1 or AMP Champ 2-557101-1

Pin Name Dir Description
112V---+12 VDC
212V---+12 VDC
312V---+12 VDC
412V---+12 VDC
53.3V---+3.3 VDC
63.3V---+3.3 VDC
7-DB(11)<->Data Bus 11
8-DB(10)<->Data Bus 10
9-DB(9)<->Data Bus 9
10-DB(8)<->Data Bus 8
11-I/O-->Input/Output
12-REQ-->Request
13-C/D-->Control/Data
14-SEL<->Select
15-MSG-->Message
16-RST<->Reset
17-ACK<--Acknowledge
18-BSY<->Busy
19-ATN<--Attention
20-P_CRCA? 
21-DB(7)<->Data Bus 7
22-DB(6)<->Data Bus 6
23-DB(5)<->Data Bus 5
24-DB(4)<->Data Bus 4
25-DB(3)<->Data Bus 3
26-DB(2)<->Data Bus 2
27-DB(1)<->Data Bus 1
28-DB(0)<->Data Bus 0
29-DB(P1)? 
30-DB(15)<->Data Bus 15
31-DB(14)<->Data Bus 14
32-DB(13)<->Data Bus 13
33-DB(12)<->Data Bus 12
345V---Ground (Signal)
355V---Ground (Signal)
365V CHARGE---Ground (Signal)
37SPINDLE SYNC?Spindle Sync
38RMT_START?Remote Start
39SCSI ID (0)---SCSI ID Bit 0
40SCSI ID (2)---SCSI ID Bit 2
4112V GROUND---+12 VDC Ground
4212V GROUND---+12 VDC Ground
4312V GROUND---+12 VDC Ground
44MATED 1? 
453.3V CHARGE---+3.3 VDC Charge
46GROUND---Ground
47SIGNAL RETURN---Ground (Signal)
48SIGNAL RETURN---Ground (Signal)
49SIGNAL RETURN---Ground (Signal)
50SIGNAL RETURN---Ground (Signal)
51SIGNAL RETURN---Ground (Signal)
52SIGNAL RETURN---Ground (Signal)
53SIGNAL RETURN---Ground (Signal)
54SIGNAL RETURN---Ground (Signal)
55SIGNAL RETURN---Ground (Signal)
56SIGNAL RETURN---Ground (Signal)
57SIGNAL RETURN---Ground (Signal)
58SIGNAL RETURN---Ground (Signal)
59SIGNAL RETURN---Ground (Signal)
60SIGNAL RETURN---Ground (Signal)
61SIGNAL RETURN---Ground (Signal)
62SIGNAL RETURN---Ground (Signal)
63SIGNAL RETURN---Ground (Signal)
64SIGNAL RETURN---Ground (Signal)
65SIGNAL RETURN---Ground (Signal)
66SIGNAL RETURN---Ground (Signal)
67SIGNAL RETURN---Ground (Signal)
68SIGNAL RETURN---Ground (Signal)
69SIGNAL RETURN---Ground (Signal)
70SIGNAL RETURN---Ground (Signal)
71SIGNAL RETURN---Ground (Signal)
72SIGNAL RETURN---Ground (Signal)
73SIGNAL RETURN---Ground (Signal)
74MATED 2? 
755V GROUND---+5 VDC Ground
765V GROUND---+5 VDC Ground
77ACTIVE LED OUT? 
78DLYD_START? 
79SCSI ID (1)---SCSI ID Bit 1
80SCSI ID (3)---SCSI ID Bit 3

5: RESERVED/NC 6: RESERVED/NC 20: -DB(P0) 36: 5 VOLT 44: 12 V GROUND 45: RESERVED/NC 46: RESERVED/NC 74: 5 V GROUND

Note: Direction is Device relative Bus (other Devices)


This information should be correct, but may be not. Please, help us to improve this document!
Is this document CORRECT or INCORRECT? Your opinion will be used to establish document status (showed at the bottom).
Pinouts.ru > Hard drives connectors pinouts listing >  Pinout of SCSI-3 External Hi D-Sub (Single-ended) and layout of 80 pin SCSI SCA-2 female connector
Document status: unknown
Source(s) of this and additional information: SCA SFF-8015 Draft Rev 3.1, from Hardware Book 0 reports
Last updated at Sat Jun 25 2005. Submit additions or corrections for this document. Is this document correct or incorrect? What is your opinion?
[Discuss at the forum] [Back to index] [SUBMIT new pinout]
This page contain parts under Copyright © 2000-2007 by pinouts.ru team.
No any portion of this webpage may be reproduced in any form without visible direct link to this page provided. Webmaster permission required in any other cases.
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.
10090 hits since March 4, 2005